The concept StraightSkeletonBuilderTraits_2 describes the requirements for the geometric traits class required by the algorithm class Straight_skeleton_builder_2<Gt,Ss>.
StraightSkeletonBuilderTraits_2::Kernel | |
A model of the Kernel concept.
| |
StraightSkeletonBuilderTraits_2::FT | |
A SqrtFieldNumberType provided by the kernel. This type is used to represent the
coordinates of the input points, of the skeleton nodes and as the event time stored in the skeleton nodes.
|
StraightSkeletonBuilderTraits_2::Equal_2 | |||
A predicate object type being a model of the Kernel::Equal_2 function object concept.
| |||
StraightSkeletonBuilderTraits_2::Left_turn_2 | |||
A predicate object type being a model of the Kernel::LeftTurn_2 function object concept.
| |||
StraightSkeletonBuilderTraits_2::Collinear_2 | |||
A predicate object type being a model of the Kernel::Collinear_2 function object concept.
| |||
StraightSkeletonBuilderTraits_2::Do_ss_event_exist_2 | |||
A predicate object type. Must provide bool operator()( EdgeTriple const& et) const, which determines if, given the 3 oriented lines defined by the 3 input edges (3 pair of points), there exist an Euclidean distance t ≥ 0 for which the corresponding 3 offset lines at t (parallel lines at an Euclidean distance of t) intersect in a single point.
| |||
StraightSkeletonBuilderTraits_2::Compare_ss_event_times_2 | |||
A predicate object type. Must provide Comparison_result operator()( EdgeTriple const& x, EdgeTriple const& y) const, which compares the times for the events determined by the edge-triples x and y. The time of an event given by an edge triple (which defines 3 oriented lines) is the Euclidean distance t at which the corresponding offset lines at t intersect in a single point.
| |||
StraightSkeletonBuilderTraits_2::Compare_ss_event_distance_to_seed_2 | |||
A predicate object type. Must provide Comparison_result operator()( Point_2 const& p, EdgeTriple const& x, EdgeTriple const& y), which compares the Euclidean distance of the points of event for x and y to the point p. The point of an event given by an edge triple (which defines 3 oriented lines) is the intersection point of the 3 corresponding offset lines at the time t of the event. It must also provide Comparison_result operator( EdgeTriple const& seed, EdgeTriple const& x, EdgeTriple const& y)() which makes the same comparison as the first overload but where the seed point is given implicitly as the point of event for seed.
| |||
StraightSkeletonBuilderTraits_2::Is_ss_event_inside_offset_zone_2 | |||
A predicate object type. Must provide bool operator()( EdgeTriple const& e, EdgeTriple const& zone), which determines if the point of event for e is inside the offset zone defined by the 3 oriented lines given by zone. An offset zone given by 3 oriented lines is the intersection of the halfplanes to the left of each oriented line.
| |||
StraightSkeletonBuilderTraits_2::Are_ss_events_simultaneous_2 | |||
A predicate object type. Must provide bool operator()( EdgeTriple const& x, EdgeTriple const& y), which determines if the events given by x and y are coincident in time and space; that is, both triples of offset lines intersect at the same point and at the same Euclidean distance from their sources.
| |||
StraightSkeletonBuilderTraits_2::Construct_ss_event_time_and_point_2 | |||
A construction object type. Must provide boost::tuple< boost::optional<FT>, boost::optional<Point_2> > operator()( EdgeTriple const& e), which given the 3 oriented lines defined by the 3 input edges (3 pair of points), returns the Euclidean distance t ≥ 0 and intersection point at which the corresponding 3 offset lines at t intersect. If the values cannot be computed, not even approximately (because of overflow for instance), an empty optional must be returned.
| |||
StraightSkeletonBuilderTraits_2::Construct_ss_vertex_2 | |||
A construction object type. Must provide Vertex operator()( Point_2 const& p), which given a Point_2 p returns a Vertex encapsulating the corresponding (x,y) pair of Cartesian coordinates.
| |||
StraightSkeletonBuilderTraits_2::Construct_ss_edge_2 | |||
A construction object type. Must provide Edge operator()( Point_2 const& s, Point_2 const& t), which given source and target points s and t returns an Edge encapsulating the corresponding input segment (in Cartesian coordinates.)
| |||
StraightSkeletonBuilderTraits_2::Construct_ss_triedge_2 | |||
A construction object type. Must provide Triedge operator()( Edge const& e0, Edge const& e1, Edge const& e2), which given the 3 edges that define an event, e0, e1 and e2, returns a Triedge encapsulating them.
|
CGAL::Straight_skeleton_builder_traits_2<K>.
CGAL::Straight_skeleton_builder_2<Gt,Ss>
CGAL::Straight_skeleton_builder_traits_2<K>